OLED 4Pin 128×64 Display Module 0.96 Inch BLUE Color
1. Size: 0.96 inch
2. Resolution: 128 x 64
3. Controlling Chip: SSD1306
4. Display Area: 21.74 x 10.86mm
5. Driving Voltage: 3.3-5V
6. Operating Temperature: -40~70 celsius
7. Interface modes: I2C/IIC
8. Light Color: Blue
OLED 4Pin 128×64 Display Module 0.96 Inch WHITE Color
1. Size: 0.96 inch
2. Resolution: 128 x 64
3. Controlling Chip: SSD1306
4. Display Area: 21.74 x 10.86mm
5. Driving Voltage: 3.3-5V
6. Operating Temperature: -40~70 celsius
7. Interface modes: I2C/IIC
8. Light Color: White
OLED 4Pin 128×64 Display Module 0.96 Inch YELLOW-BLUE Color
1. Size: 0.96 inch
2. Resolution: 128 x 64
3. Controlling Chip: SSD1306
4. Display Area: 21.74 x 10.86mm
5. Driving Voltage: 3.3-5V
6. Operating Temperature: -40~70 celsius
7. Interface modes: I2C/IIC
8. Light Color: Yellow & Blue
OLED 6Pin 128×64 Display Module 0.96 Inch YELLOW-BLUE Color
1. Size: 0.96 inch
2. Resolution: 128 x 64
3. Controlling Chip: SSD1306
4. Display Area: 21.74 x 10.86mm
5. Driving Voltage: 3.3-5V
6. Operating Temperature: -40~70 celsius
7. Interface modes: I2C/IIC
8. Light Color: Yellow & Blue
PIC Programmer Adaptor
The PIC ICD2 PICKit2 PICKIT3 Universal Programming Adapter Programmer Board is designed to work in conjunction with the popular PICkit 2 or PICkit3 programmer.
Pir Sensor HC-SR501
1. Wide Working Voltage Range: DC 4.5V- 20V
2. Current Drain: <60uA
3. Detection Angle: <140°
4. Detection Distance: 3 to 7m (can be adjusted)
5. Blockade time: 2.5s (Default)
6. Work temperature: -20-+80°C
Power Supply for Breadboard DC 12v to DC 5v-3.3v
1. Breadboard power supply module, compatible with 5V, 3.3V.
2. Apply to MB102 breadboard
3. Input voltage: 6.5-12 V (DC) or USB power supply
4. Output voltage: 3.3V/5V can switch over
5. Maximum output current: <700 ma
6. Fluctuation two road independent control can switch over to 0 V, 3.3 V, 5 V
7. On-board two groups of 3.3V, 5V DC output plug pin, convenient external lead use.
Pulse Sensor – Heart Rate Detector
1. A Color-Coded Cable, with a standard male header connectors. Plug it straight into an Arduino or a Breadboard. No soldering is required.
2. The Pulse Sensor has 3 holes around the outside edge which make it easy to sew it into almost anything.
3. Visualization software (made in Processing) to instantly see the output of the sensor and for troubleshooting.
Rain Drop Sensor
1. Operating voltage: 5V
2. Provide both digital and analog output
3. Adjustable sensitivity
4. Output LED indicator
5. Compatible with Arduino
6. TTL Compatible
7. Bolt holes for easy installation
Raspberry Pi Camera – 5MP
1. Resolution: 5 MP
2. Interface Type: CSI(Camera Serial Interface)
3. Dimensions: 25x23x8 (LxWxH) mm
4. Supported Video Formats: 1080p @ 30fps, 720p @ 60fps and 640x480p 60/90 video
5. Fully Compatible with Raspberry Pi 3 and 4 Model B
6. Plug-n-Play camera for Raspberry Pi 3 and 4 Model B.
RC522 RFID Reader Writer
1. Voltage: DC 3.3V (Do not use 5V supply)
2. Operating Current :13-26mA
3. Idle Current :10-13mA
4. Operating Frequency: 13.56MHz
5. Highly integrated analog circuitry to demodulate and decode responses
6. Supports ISO/IEC 14443 A/MIFARE
7. Typical operating distance in reading/Write mode up to 50 mm
RFID Card 125KHZ Thin
1. Contactless transmission of data and supply energy (no battery needed)
2. Operating distance: Up to 1 to 5 cm (Depending on Antenna Geometry)
3. Operating frequency: 125KHz
4. Data transfer: 106 kbit/s
5. Data integrity: 16 Bit CRC, parity, bit coding bit counting
6. Anticollision