1 Channel Relay Board 5V with Optocoupler
1. Channel – 1
2. Trigger Voltage (VDC) – 5
3. Switching Voltage (VAC) – 250@10A
4. Switching Voltage (VDC) – 30@10A
100 Ohm 1/8W Through Hole Resistor (Pack of 5)
1. Resistance: 100 Ohm
2. Tolerance: ±5%
3. Max. Working Voltage: 250V
4. Temperature Coefficient of Resistance: 50PPM/°C
10K Ohm 1/8W Through Hole Resistor (Pack of 5)
1. Resistance: 10K Ohm
2. Tolerance: ±5%
3. Max. Working Voltage: 250V
4. Temperature Coefficient of Resistance: 50PPM/°C
1K Ohm 1/8W Through Hole Resistor (Pack of 5)
1. Resistance: 1K Ohm
2. Tolerance: ±5%
3. Max. Working Voltage: 250V
4. Temperature Coefficient of Resistance: 50PPM/°C
2 Channel Relay Board 5V
1. No. of Channel: 2
2. Trigger Voltage: 5VDC
3. Triode drive, increasing relay coil
4. High impedance controller pin
5. Pull-down circuit for the avoidance of malfunction
6. Power supply indicator and Control indicator lamp
7. Power supply and relay instructions, lit, the disconnect is off;
8. The input signal, signal, common Terminal and start conducting;
220 Ohm 1/8W Through Hole Resistor (Pack of 5)
1. Resistance: 220 Ohm
2. Tolerance: ±5%
3. Max. Working Voltage: 250V
4. Temperature Coefficient of Resistance: 50PPM/°C
330 Ohm 1/8W Through Hole Resistor (Pack of 5)
1. Resistance: 330 Ohm
2. Tolerance: ±5%
3. Max. Working Voltage: 250V
4. Temperature Coefficient of Resistance: 50PPM/°C
4 Channel Relay Board 5V
1. No. of Channel: 4
2. Trigger Voltage: 5VDC
3. Triode drive, increasing relay coil
4. High impedance controller pin
5. Pull-down circuit for the avoidance of malfunction
6. Power supply indicator and Control indicator lamp
7. Power supply and relay instructions, lit, the disconnect is off;
8. The input signal, signal, common Terminal and start conducting;
650NM Laser Diode
1. Output Power: 5mW
2. Working Voltage: 5V DC
3. Working temperature: -10 ℃~+40 ℃
4. Housing material: Copper
5. Working life: more than 2000 hours
6. Spot mode: Dot Facula (continuous output)
7. Laser wavelength: 650nm red-colored.
8. Operating current: <40mA
9. Power lead length: 120mm.
8 Channel Relay Board 5V
1. Channel: 8 channel
2. Relay Operating Voltage: 5V
3. One normally closed contact and one normally open contact
4. Triode drive, increasing relay coil
5. High impedance controller pin
6. Pull-down circuit for the avoidance of malfunction
7. Power supply indicator and Control indicator lamp
8. Power supply and relay instructions, lit, the disconnect is off;
9V Battery Connector With DC Pin
1. Excellent material
2. It is an environmental 9V battery buckle
3. The Cable Length: 12cm Approx.
4. Convenient for connecting a battery to your application.
5. Save power and protect the environment
6. Good electrical conductivity and comfortable sense of touch
Aligator Clip Jumper Wire
1. Colour: Red, Green, Yellow, White, and Black, etc.
2. Cable length: 45 cm.
3. Net weight: 82 gm.
4. They are very useful for connecting components to wires.
5. It is insulation covered clips connected to the wire from both ends.