It is a 10k Ohm 0.25W Metal Film Resistor. This resistor is for through-hole applications.
10K Ohm 1/8W Through Hole Resistor (Pack of 5)
₹10.00 ₹12.00
Price Summary
- ₹12.00
- ₹10.00
- 17%
- ₹10.00
- Overall you save ₹2.00 (17%) on this product
1. Resistance: 10K Ohm
2. Tolerance: ±5%
3. Max. Working Voltage: 250V
4. Temperature Coefficient of Resistance: 50PPM/°C
Weight | 0.01 kg |
---|---|
Dimensions | 0.45 × 0.35 × 1.9 cm |
Be the first to review “10K Ohm 1/8W Through Hole Resistor (Pack of 5)” Cancel reply
Related Products
Male To Male Jumper Wires (20cm) – 40 Pieces
1. 40P color DuPont line
2. Length: 200mm
3. Weight: 30 gm
4. Compatible with 2.54mm spacing pin headers
5. 40pcs chromatic male to male color jump wire
6. High quality and in good working condition
7. Durable and reusable
8. Easy to install and use
650NM Laser Diode
1. Output Power: 5mW
2. Working Voltage: 5V DC
3. Working temperature: -10 ℃~+40 ℃
4. Housing material: Copper
5. Working life: more than 2000 hours
6. Spot mode: Dot Facula (continuous output)
7. Laser wavelength: 650nm red-colored.
8. Operating current: <40mA
9. Power lead length: 120mm.
8 Channel Relay Board 5V
1. Channel: 8 channel
2. Relay Operating Voltage: 5V
3. One normally closed contact and one normally open contact
4. Triode drive, increasing relay coil
5. High impedance controller pin
6. Pull-down circuit for the avoidance of malfunction
7. Power supply indicator and Control indicator lamp
8. Power supply and relay instructions, lit, the disconnect is off;
Female To Female Jumper Wires (20cm) – 40 Pieces
1. 40P color DuPont line
2. Length: 200mm
3. Weight: 30 gm
4. Compatible with 2.54mm spacing pin headers
5. 40pcs chromatic female to female color jump wire
6. High quality and in good working condition
7. Durable and reusable
8. Easy to install and use
1K Ohm 1/8W Through Hole Resistor (Pack of 5)
1. Resistance: 1K Ohm
2. Tolerance: ±5%
3. Max. Working Voltage: 250V
4. Temperature Coefficient of Resistance: 50PPM/°C
TTP223 Touch Sensor Module
1. Power supply voltage(VCC): 2.0, 3, 5.5 V.
2. Output high VOH: 0.8VCC V
3. Output low VOL: 0.3VCC V
4. Response time (touch mode) : 60 mS
5. Response time (low power mode) : 220 mS
6. Can replace the traditional touch of a button
7. Four M2 screws positioning holes for easy installation
4 Channel Relay Board 5V
1. No. of Channel: 4
2. Trigger Voltage: 5VDC
3. Triode drive, increasing relay coil
4. High impedance controller pin
5. Pull-down circuit for the avoidance of malfunction
6. Power supply indicator and Control indicator lamp
7. Power supply and relay instructions, lit, the disconnect is off;
8. The input signal, signal, common Terminal and start conducting;
Motor Driver – L293D
1. The driver two holes of 3 mm dia.
2. Male burg-stick connectors for supply, ground and input connection.
3. Screw terminal connectors for easy motor connection.
4. High noise immunity inputs.
5. Operating Voltage(VDC): 4.5 to 12
6. Peak Current (A): 600 mA
7. No. of Channels: 1
Keypad 4*4 Membrane
1. Ultra-thin design & adhesive backing provides easy integration to any project
2. Excellent price-performance ratio
3. Easy communication with any microcontroller
4. 5 pins 2.54mm pitch connector, 4×4 type – 16 keys.
5. Sticker can peel off for adhesive mounting.
6. Operating Voltage (V): 12 DC
Aligator Clip Jumper Wire
1. Colour: Red, Green, Yellow, White, and Black, etc.
2. Cable length: 45 cm.
3. Net weight: 82 gm.
4. They are very useful for connecting components to wires.
5. It is insulation covered clips connected to the wire from both ends.
220 Ohm 1/8W Through Hole Resistor (Pack of 5)
1. Resistance: 220 Ohm
2. Tolerance: ±5%
3. Max. Working Voltage: 250V
4. Temperature Coefficient of Resistance: 50PPM/°C
NE555 Timer Switch Adjustable Relay Board
1. Module based on the NE555 chip.
2. Input voltage: DC 12V
3. Adjustable time: 0-10 s
4. AC Control voltage: 250V/max. 10A
5. Max. load: 2200W
There are no reviews yet.