The USB ASP AVR Programming Device for ATMEL processors is a USB in-circuit programmer for Atmel AVR controllers. USB ASP AVR Programming Device for ATMEL Processors simply consists of an ATMega88 or an ATMega8 and a couple of passive components. The programmer uses a firmware-only USB driver; no special USB controller is needed.



AVR ASP Programmer
₹375.00 ₹380.00
Price Summary
- ₹380.00
- ₹375.00
- 1%
- ₹375.00
- Overall you save ₹5.00 (1%) on this product
1. Compatible Chips:
i. ATMega Series
ii. Tiny Series
iii. Classic Series
iv. CAN Series
v. PWM Series
Weight | 0.2 kg |
---|---|
Dimensions | 8 × 5 × 2 cm |
Be the first to review “AVR ASP Programmer” Cancel reply
Related Products
DF Mini MP3 Player Module
1. Supports sampling rates (KHz): 8 / 11.025 / 12/16 / 22.05 / 24/32 / 44.1 / 48
2. 24-bit DAC output, dynamic range support: 90dB, SNR support: 85dB
3. Fully supports FAT16, FAT32 file system
4. Maximum support 32G TF card
5. Support U disk to 32G, 64M bytes of NORFLASH
6. A variety of control modes are available. IO control mode, serial mode, AD key control mode
IIC/I2C Serial Interface Adapter Module
1. 5V power supply.
2. Serial I2C control of LCD display using PCF8574.
3. Backlight can be enabled or disabled via a jumper on the board.
4. Contrast control via a potentiometer.
5. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
DS3231 RTC Module
1. Two-wire I2C interface.
2. Hour: Minutes: Seconds AM/PM.
3. Day Month, Date – Year.
4. DS1307 based RTC (Battery include).
5. 1Hz output pin.
6. Available in 8-pin DIP or SOIC
DC 12v to 3.3v 5v TTL module
1. Input Voltage: 12V
2. Connector: 5.5mm DC Jack
3. Output power on/off switch
4. Two-row multiple pin outputs, easy to use and connect
5. Outputs
o 3.3V DC at 800mA maximum current
o 5.0V DC at 800mA maximum current
o 12V DC (the 12V output is directly connected to the input, i.e. with 12VDC input, this output will be 12VDC; with 9VDC input, this output will be 9VDC)
JoyStick Shield Module
1. 2-Axis joystick
2. Bluetooth / Serial interface
3. I2C interface
4. nRF24L01 interface
5. Nokia 5110 LCD interface
6. Interface connector
7. Power switch to switch between 3.3 and 5V
USB to TTL CH340 Based
1. Built-in USB to TTL Transfer chip.
2. Designed to be used for USB to TTL electronic projects.
3. TTL interface output, easy to connect to your MCU.
4. Dual 3.3V and 5V Power output, work with 3.3v and 5 V target device.
5. The mini-module is designed specifically for STC download and ARDUINO PRO supports all series of STC
6. Supports WIN7/VISTA/MAC/LINUX(32 bit /64-bit system)
MP3 Module With Power Amplifier
1. Support MP3 format, playing power on automatically.
2. When mp3 is played the red LED flashes.
3. Support U disk (test 32G), TF Card (test 16G) play mode; power on default.
4. Buttons can be adjusted up and down to control songs, volume up and down, pause or play, mode switching.
5. Press menu button enter the single / all song play mode.
Joystick Module
1. Dimensions: 34 x 34 x 15 (LxWxH) mm.
2. Weight: 10gm (without Hat).
3. 2.54mm pin interface leads.
4. Operating Voltage: 5V.
5. Long service life and stable performance.
6. Standard interface and electronic building blocks.
7. Widely use in Arduino DIY projects.
SD Card Module for Arduino
1. All SD SPI pins output, MOSI, SCK, MISO, and CS.
2. Support 5V/3.3V input.
3. This module can handle 2GB SD cards.
4. Size:4.7 x 3.1 cm.
5. LED indicator.
6. SD Card Holder.
7. Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
Logic Level Converter module 3.3 V To 5V TTL
1. Material: Plastic + metal.
2. Colour: Red and Yellow.
3. Portable, small, easy to use.
4. Comes with 2 rows of 6 pin, unsoldered.
5. The compatible breadboard can be directly inserted into the breadboard.
Antenna – GSM PCB
1. Name: 2G 3G IPEX antenna
2. Connector type: ipx13
3. Gain definition: 3dBi (Typical)
4. Frequency band definition: 900-1500 MHz
5. Impedance definition: 50 ohm
6. Total length: as shown in Figure
7. Impedance 50 Ohm
PIC Programmer Adaptor
The PIC ICD2 PICKit2 PICKIT3 Universal Programming Adapter Programmer Board is designed to work in conjunction with the popular PICkit 2 or PICkit3 programmer.
There are no reviews yet.