The USB ASP AVR Programming Device for ATMEL processors is a USB in-circuit programmer for Atmel AVR controllers. USB ASP AVR Programming Device for ATMEL Processors simply consists of an ATMega88 or an ATMega8 and a couple of passive components. The programmer uses a firmware-only USB driver; no special USB controller is needed.
AVR ASP Programmer
₹380.00 Original price was: ₹380.00.₹375.00Current price is: ₹375.00.
Price Summary
- ₹380.00
- ₹375.00
- 1%
- ₹375.00
- Overall you save ₹5.00 (1%) on this product
1. Compatible Chips:
i. ATMega Series
ii. Tiny Series
iii. Classic Series
iv. CAN Series
v. PWM Series
Weight | 0.2 kg |
---|---|
Dimensions | 8 × 5 × 2 cm |
Be the first to review “AVR ASP Programmer” Cancel reply
Related Products
RFID Card 125KHZ Thin
1. Contactless transmission of data and supply energy (no battery needed)
2. Operating distance: Up to 1 to 5 cm (Depending on Antenna Geometry)
3. Operating frequency: 125KHz
4. Data transfer: 106 kbit/s
5. Data integrity: 16 Bit CRC, parity, bit coding bit counting
6. Anticollision
MT3608 DC-DC Boost 2A Module
1. It’s efficient up to 93%
2. It can source a good amount of current
3. The maximum output current: 2A
4. Input voltage: 2V-24V DC
5. The maximum output voltage: 5V-28V DC
Logic Level Converter module 5V To 3.3V TTL
1. Material: Plastic + metal.
2. Colour: Red and Yellow.
3. Portable, small, easy to use.
4. Comes with 2 rows of 6 pin, unsoldered.
5. The compatible breadboard can be directly inserted into the breadboard.
USB to TTL CH340 Based
1. Built-in USB to TTL Transfer chip.
2. Designed to be used for USB to TTL electronic projects.
3. TTL interface output, easy to connect to your MCU.
4. Dual 3.3V and 5V Power output, work with 3.3v and 5 V target device.
5. The mini-module is designed specifically for STC download and ARDUINO PRO supports all series of STC
6. Supports WIN7/VISTA/MAC/LINUX(32 bit /64-bit system)
RFID Keytag 13.56MHz
1. Material: ABS
2. Dimension(LxWxH): 43.7×30.5×5.3mm
3. Response Frequency: 13.56MHz
4. Chip type: FM1108 Fudan Chip
5. Memory capacity: 8 kbit
6. Designed for the RFID 13.56MHz duplicator. can copy all the ID card, such as Access Card, District Card, Parking etc.
RC522 RFID Reader Writer
1. Voltage: DC 3.3V (Do not use 5V supply)
2. Operating Current :13-26mA
3. Idle Current :10-13mA
4. Operating Frequency: 13.56MHz
5. Highly integrated analog circuitry to demodulate and decode responses
6. Supports ISO/IEC 14443 A/MIFARE
7. Typical operating distance in reading/Write mode up to 50 mm
DF Mini MP3 Player Module
1. Supports sampling rates (KHz): 8 / 11.025 / 12/16 / 22.05 / 24/32 / 44.1 / 48
2. 24-bit DAC output, dynamic range support: 90dB, SNR support: 85dB
3. Fully supports FAT16, FAT32 file system
4. Maximum support 32G TF card
5. Support U disk to 32G, 64M bytes of NORFLASH
6. A variety of control modes are available. IO control mode, serial mode, AD key control mode
Joystick Module
1. Dimensions: 34 x 34 x 15 (LxWxH) mm.
2. Weight: 10gm (without Hat).
3. 2.54mm pin interface leads.
4. Operating Voltage: 5V.
5. Long service life and stable performance.
6. Standard interface and electronic building blocks.
7. Widely use in Arduino DIY projects.
SD Card Module for Arduino
1. All SD SPI pins output, MOSI, SCK, MISO, and CS.
2. Support 5V/3.3V input.
3. This module can handle 2GB SD cards.
4. Size:4.7 x 3.1 cm.
5. LED indicator.
6. SD Card Holder.
7. Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
DC 12v to 3.3v 5v TTL module
1. Input Voltage: 12V
2. Connector: 5.5mm DC Jack
3. Output power on/off switch
4. Two-row multiple pin outputs, easy to use and connect
5. Outputs
o 3.3V DC at 800mA maximum current
o 5.0V DC at 800mA maximum current
o 12V DC (the 12V output is directly connected to the input, i.e. with 12VDC input, this output will be 12VDC; with 9VDC input, this output will be 9VDC)
Antenna – GSM PCB
1. Name: 2G 3G IPEX antenna
2. Connector type: ipx13
3. Gain definition: 3dBi (Typical)
4. Frequency band definition: 900-1500 MHz
5. Impedance definition: 50 ohm
6. Total length: as shown in Figure
7. Impedance 50 Ohm
Logic Level Converter module 3.3 V To 5V TTL
1. Material: Plastic + metal.
2. Colour: Red and Yellow.
3. Portable, small, easy to use.
4. Comes with 2 rows of 6 pin, unsoldered.
5. The compatible breadboard can be directly inserted into the breadboard.
There are no reviews yet.